switch to fastled because of too few pios

soundcube-firmware/soundcube-firmware.ino

@@ -22,8 +22,8 @@ PWMAudio ui_snd(8);
 
 enum BUTTON {CVINL, CVINR, INL, INR, OUTR, OUTL, CVOUTR, CVOUTL, RIGHT, LEFT, SELECT, DEBUG1, DEBUG2, DEBUG3};
 
-Adafruit_NeoPixel edge_pixels(11, 4, NEO_GRB + NEO_KHZ800);
 Adafruit_NeoPixel ui_pixels(74, 5, NEO_GRB + NEO_KHZ800);
+Adafruit_NeoPixel edge_pixels(11, 4, NEO_GRB + NEO_KHZ800);
 
 volatile bool flag = false;
 volatile bool click = false;
@@ -72,7 +72,7 @@ void pwm_audio_callback() {
           click = false;
         }
       } else {
-        digitalWriteFast(7, LOW);
+        digitalWrite(7, LOW);
         ui_snd.write(0);
         counter = 0;
       }
@@ -85,9 +85,7 @@ void tca_irq() {
 
 void setup() {
   Serial.begin();
-  while (!Serial) {
+  delay(2000);
-    ;
-  }
 
   pinMode(21, INPUT_PULLUP);
   sd_card_detected = !digitalRead(21);
@@ -102,13 +100,14 @@ void setup() {
   if(sdInitialized && SD.exists("/click.wav")) {
     File click = SD.open("/click.wav");
     int click_bytes = 0;
-    int32_t maxv = 0;
+    int16_t maxv = 0;
     while (click.available() || click_bytes == UI_SAMPLERATE-1) {
-      int32_t sample = click.read() * 64;
+      int16_t sample = click.read() * 32;
       if(abs(sample) > maxv) maxv = sample;
       beep[click_bytes] = sample;
       click_bytes++;
     }
+    click.close();
     
     beep_length = click_bytes;
     Serial.print("Read ");
@@ -153,9 +152,14 @@ void setup() {
 
   digitalWrite(7, LOW);
 
-  edge_pixels.begin();  // INITIALIZE NeoPixel strip object (REQUIRED)
+  edge_pixels.begin();
-  ui_pixels.begin();    // INITIALIZE NeoPixel strip object (REQUIRED)
+  delay(100);
+  ui_pixels.begin();
   
+  digitalWrite(6, HIGH);
+  delay(50);
+  digitalWrite(6, LOW);
+
   // i2s.setDOUT(14);
   // i2s.setDIN(15);
   // i2s.setBCLK(16); // 
@@ -172,6 +176,7 @@ void setup() {
   //   i2s.write16(l, r);
   // }
 }
+
 int active = 0;
 int active_led_ring = 0;
 
@@ -179,91 +184,81 @@ uint32_t lastTime = 0;
 int32_t position = 0;
 
 void loop() {
-  edge_pixels.clear();  // Set all pixel colors to 'off'
   ui_pixels.clear();    // Set all pixel colors to 'off'
+  edge_pixels.clear();  // Set all pixel colors to 'off'
   
+  position = ENC.getCumulativePosition();
+
   sd_card_detected = !digitalRead(21);
   if(sd_card_detected) edge_pixels.setPixelColor(8, edge_pixels.Color(0,25,0));
   if(!sd_card_detected) edge_pixels.setPixelColor(8, edge_pixels.Color(25,0,0));
 
-  position = ENC.getCumulativePosition();
-
-  // if (millis() - lastTime >= 100)
-  // {
-  //   lastTime = millis();
-  //   Serial.print(ENC.getCumulativePosition());
-  //   Serial.print("\t");
-  //   Serial.println(ENC.getRevolutions());
-  // }
-
-  // LED Ring leeren
-  for (int i = 0; i < 48; i++) {
-    ui_pixels.setPixelColor(i + 3, edge_pixels.Color(0, 0, 0));
-  }
-
-  // flag = true when a button is pushed
-  if (flag) {
-    int val = TCA.read16();
-    Serial.println(val, BIN);
-    
-    for(int i = 0; i < 16; i++){
-      buttons[i] = ~(val >> i) & 0x01;
-      Serial.print(buttons[i]);
-      Serial.print(" ");
-    }
-    Serial.println();
-
-    flag = false;
-    if (HAPTIC) {
-      digitalWrite(6, HIGH);
-    }
-    // Make beep
-    if (AURAL) {
-      digitalWriteFast(7, HIGH);
-      click = true;
-    }
-    // Make vibration
-    if(HAPTIC){
-      if(!AURAL) delay(50);
-      digitalWrite(6, LOW);
-    }
-    // Flash led ring 
-    for (int i = 0; i < 48; i++) {
-        ui_pixels.setPixelColor(i + 3, edge_pixels.Color(0, 15, 0));
-    }
-    // Switch through LED matrix
-    if(buttons[RIGHT]) active++;
-    if(buttons[LEFT]) active--;
-    if(active == 13) active = 0;
-    if(active == -1) active = 12;
-  }
-
   // EDGE LEDs
   for (int i = 0; i < 8; i++) {
     edge_pixels.setPixelColor(i, edge_pixels.Color(config.edge_color_r, config.edge_color_g, config.edge_color_b));
   }
+  
+  // LED Ring leeren
+  for (int i = 0; i < 48; i++) {
+    ui_pixels.setPixelColor(i + 3, ui_pixels.Color(0, 0, 0));
+  }
+
+  // flag = true when a button is pushed
+  if (flag) {
+    int val = TCA.read16();
+    
+    for(int i = 0; i < 16; i++){
+      buttons[i] = ~(val >> i) & 0x01;
+    }
+    
+    // Make vibration
+    if (HAPTIC) {
+      digitalWrite(6, HIGH);
+      delay(50);
+      digitalWrite(6, LOW);
+    }
+
+    // Make beep
+    if (AURAL) {
+      digitalWrite(7, HIGH);
+      click = true;
+    }
+
+    // Flash led ring 
+    for (int i = 0; i < 48; i++) {
+        ui_pixels.setPixelColor(i + 3, ui_pixels.Color(0, 15, 0));
+    }
+
+    // Switch through LED matrix
+    if(buttons[RIGHT]) active++;
+    if(buttons[LEFT]) active--;
+    if(active == 13) active = 0;
+    if(active == -1) active = 12;
+    
+    flag = false;
+  }
 
   // Rotary button LEDs
-  ui_pixels.setPixelColor(0, edge_pixels.Color(0, 0, 15));
+  ui_pixels.setPixelColor(0, ui_pixels.Color(0, 0, 15));
-  ui_pixels.setPixelColor(1, edge_pixels.Color(0, 0, 15));
+  ui_pixels.setPixelColor(1, ui_pixels.Color(0, 0, 15));
-  ui_pixels.setPixelColor(2, edge_pixels.Color(0, 0, 15));
+  ui_pixels.setPixelColor(2, ui_pixels.Color(0, 0, 15));
 
   // empty LED matrix
   for (int i = 0; i < 13; i++) {
-    ui_pixels.setPixelColor(i + 3 + 48 + 4, edge_pixels.Color(0, 0, 0));
+    ui_pixels.setPixelColor(i + 3 + 48 + 4, ui_pixels.Color(0, 0, 0));
   }
   
   // set active LED matrix LED
-  ui_pixels.setPixelColor(active + 3 + 48 + 4, edge_pixels.Color(255, 255, 255));
+  ui_pixels.setPixelColor(active + 3 + 48 + 4, ui_pixels.Color(255, 255, 255));
 
   if(position < 0) position += 4096;
   active_led_ring = (position / 32) % 48;
   
   // set active LED ring LED
-  ui_pixels.setPixelColor(active_led_ring + 3, edge_pixels.Color(255, 255, 255));
+  ui_pixels.setPixelColor(active_led_ring + 3, ui_pixels.Color(255, 255, 255));
 
-  edge_pixels.show();
   ui_pixels.show();
+  edge_pixels.show();
 
   delay(1); // wait 1ms
 }